A novel concept for integration of flame-assisted fuel cells (FFC) with a gas turbine is analyzed in this paper. Six different fuels (CH4, C3H8, JP-4, JP-5, JP-10(L), and H2) are investigated for the analytical model of the FFC integrated gas turbine hybrid system. As equivalence ratio increases, the efficiency of the hybrid system increases initially then decreases because the decreasing flow rate of air begins to outweigh the increasing hydrogen concentration. This occurs at an equivalence ratio of 2 for CH4. The thermodynamic cycle is analyzed using a temperature entropy diagram and a pressure volume diagram. These thermodynamic diagrams show as equivalence ratio increases, the power generated by the turbine in the hybrid setup decreases. Thermodynamic analysis was performed to verify that energy is conserved and the total chemical energy going into the system was equal to the heat rejected by the system plus the power generated by the system. Of the six fuels, the hybrid system performs best with H2 as the fuel. The electrical efficiency with H2 is predicted to be 27%, CH4 is 24%, C3H8 is 22%, JP-4 is 21%, JP-5 is 20%, and JP-10(L) is 20%. When H2 fuel is used, the overall integrated system is predicted to be 24.5% more efficient than the standard gas turbine system. The integrated system is predicted to be 23.0% more efficient with CH4, 21.9% more efficient with C3H8, 22.7% more efficient with JP-4, 21.3% more efficient with JP-5, and 20.8% more efficient with JP-10(L). The sensitivity of the model is investigated using various fuel utilizations. When CH4 fuel is used, the integrated system is predicted to be 22.7% more efficient with a fuel utilization efficiency of 90% compared to that of 30%.

High-entropy alloys possessing mechanical, chemical, and electrical properties that far exceed those of conventional alloys have the potential to make a significant impact on many areas of engineering. Identifying element combinations and configurations to form these alloys, however, is a difficult, time-consuming, computationally intensive task. Machine learning has revolutionized many different fields due to its ability to generalize well to different problems and produce computationally efficient, accurate predictions regarding the system of interest. In this thesis, we demonstrate the effectiveness of machine learning models applied to toy cases representative of simplified physics that are relevant to high-entropy alloy simulation. We show these models are effective at learning nonlinear dynamics for single and multi-particle cases and that more work is needed to accurately represent complex cases in which the system dynamics are chaotic. This thesis serves as a demonstration of the potential benefits of machine learning applied to high-entropy alloy simulations to generate fast, accurate predictions of nonlinear dynamics.

This thesis explores the potential for software to act as an educational experience for engineers who are learning system dynamics and controls. The specific focus is a spring-mass-damper system. First, a brief introduction of the spring-mass-damper system is given, followed by a review of the background and prior work concerning this topic. Then, the methodology and main approaches of the system are explained, as well as a more technical overview of the program. Lastly, a conclusion and discussion of potential future work is covered. The project was found to be useful by several engineers who tested it. While there is still plenty of functionality to add, it is a promising first attempt at teaching engineers through software development.

The purpose of this project was to develop a system capable of launching projectiles at a curved trajectory. This system effectively imparts spin on projectiles, enabling controlled indirect fire for the intended use of military operations. Through this proof of concept, it was determined whether a scaled system would be a viable solution to the issue of controlled indirect fire in dense urban areas. Using a series of coaxial motors with independently controlled speeds, it was possible to alter the horizontal and vertical displacement of objects in flight.

STEM programs are the programs for the future. Technology is advancing at a rapid speed and the world is trying to keep up. Engineering is leading the charge within that because engineers are always at the forefront of innovation. However, just the prospect of growth is not enough for students to want to become professional engineers. Black female students have the desire to better their knowledge by going to institutions of higher education, but they do not share that same passion for engineering education. This study aims to understand that. This research is looking into retention factors for students in engineering and how those factors can be transferred to Black women. It was found that factors like bias training for students and faculty, integration to engineering organizations, getting more Black female professors and faculty, and introduction to prerequisite courses like calculus and physics to Black females in grade school.

As a result of the increase of pollution related to industrialization in Vietnam, acid rain has become a prevalent issue for Vietnamese farmers who are forced to rinse their crops – risking damage due to overwatering and poor harvest. Thus, the team was motivated to develop a solution to harmful impacts of acidic rainwater by creating a system with the ability to capture rainwater and determine its level of acidity in order to optimize the crop watering process, and promote productive crops. By conducting preliminary research on rainfall and tropical climate in Vietnam, existing products on the market, and pH sensors for monitoring and device material, the team was able to design a number of devices to collect, store, and measure the pH of rainwater. After developing a number of initial design requirements based on the needs of the farmers, a final prototype was developed using the best aspects of each initial design. Tests were conducted with varying structural and aqueous materials to represent a broad range of environmental conditions. While the scope of the project was ultimately limited to prototyping purposes, the principles explored throughout this thesis project can successfully be applied to a fully-functioning production model available for commercial use on Vietnamese farms. Given more time for development, improvements would be made in the extent of materials tested, and the configuration of electronics and data acquisition, in order to further optimize the process of determining rainwater acidity.

As a result of the increase of pollution related to industrialization in Vietnam, acid rain has become a prevalent issue for Vietnamese farmers who are forced to rinse their crops – risking damage due to overwatering and poor harvest. Thus, the team was motivated to develop a solution to harmful impacts of acidic rainwater by creating a system with the ability to capture rainwater and determine its level of acidity in order to optimize the crop watering process, and promote productive crops. By conducting preliminary research on rainfall and tropical climate in Vietnam, existing products on the market, and pH sensors for monitoring and device material, the team was able to design a number of devices to collect, store, and measure the pH of rainwater. After developing a number of initial design requirements based on the needs of the farmers, a final prototype was developed using the best aspects of each initial design. Tests were conducted with varying structural and aqueous materials to represent a broad range of environmental conditions. While the scope of the project was ultimately limited to prototyping purposes, the principles explored throughout this thesis project can successfully be applied to a fully-functioning production model available for commercial use on Vietnamese farms. Given more time for development, improvements would be made in the extent of materials tested, and the configuration of electronics and data acquisition, in order to further optimize the process of determining rainwater acidity.

The objective of this report is to discover a skyhook’s ability to change the plane of another spacecraft’s orbit while ensuring that each vehicle’s orbital energy remains constant. Skyhooks are a proposed momentum exchange device in which a tether is attached to a counterweight at one end and at the other, a capturing device intended to intercept rendezvousing spacecraft. Trigonometric velocity vector relations, along with objective comparisons to traditionally proposed uses for skyhooks and gravity-assist maneuvers were responsible for the ultimate parameterization of the proposed energy neutral maneuver. From this methodology, it was determined that a spacecraft’s initial relative velocity vector must be perpendicular to, and rotated about the skyhook’s total velocity vector if it is to benefit from an energy neutral plane change maneuver. A quaternion was used to model the rotation of the incoming spacecraft’s relative velocity vector. The potential post-maneuver spacecraft orbits vary in their inclinations depending on the ratio between the skyhook and spacecraft’s total velocities at the point of rendezvous as defined by the parameter called the alpha criterion. For many cases, the proposed maneuver will serve as a desirable alternative to currently practiced propulsive plane change methods because it does not costly require a substantial amount of propellant. The proposed maneuver is also more accessible than alternative methods that involve gravity-assist and aerodynamic forces. Additionally, by avoiding orbital degradation through the achievement of unchanging total orbital energy, the skyhook will be able to continually and self-sustainably provide plane changes to any spacecraft that belong to orbits that abide by the identified parameters.